Scissors - Page 29 of 48

Ribbon Slot Stuffing

Steps:

Adult Prep: Use the Scissors to cut three tight, narrow slots (about 1.5 inches long) into the Cardboard or the lid of the Container. Secure the Cardboard/lid tightly using Masking Tape.
Give the child long strips of Ribbon. Encourage them to use both hands to tear the Ribbon into small, stamp-sized pieces. Tearing wakes up the hand muscles!
Ask your child to hold the container steady with their helper hand (proximal stability) while it sits on the table.
Pick up one torn Ribbon piece. Crumple it tightly into a small ball using only their fingertips (working on pincer grasp and in-hand manipulation).
Aim the crumpled ribbon ball at a slot. Use a controlled, firm push with the index finger or thumb to send the ribbon piece completely inside the container. Repeat until the container is full!

Safety Tip:
Ribbon pieces are small objects. Constant and direct adult supervision is required throughout the activity, as they pose a choking hazard for children under five.

Felt Resistance Wall

Steps:

Adult Prep: Cut a sturdy rectangle from the cardboard. Cut 5 to 6 narrow strips of felt, about 1 inch wide.
Help your child glue the felt strips vertically onto the cardboard. Leave a very narrow gap between each felt strip to create resistant channels.
Once the glue is completely dry, have your child hold the cardboard firmly with their helper hand to keep the wall steady.
Challenge your child to pick up a craft stick. Push the stick straight through one of the narrow felt channels. This requires controlled force.
Continue inserting all the sticks into the wall, working to keep the cardboard from tipping or moving during the push.
When finished, gently pull the sticks out (working those muscles again!) and repeat the building process.

Safety Tip:
Maintain constant adult supervision, especially during the preparation phase involving scissors and glue. Ensure the child pushes the sticks away from their face and body to prevent accidental poking.

Paper Crease Tunnels

Steps:

Adult Step: Use scissors to cut 8-10 narrow slits across the top surface of the egg carton. The slits should be tight, offering resistance.
Draw several long, 1-inch wide strips onto the construction paper using a marker. Encourage your child to use their helper hand to cut carefully along the lines.
Take one paper strip. Fold it in half lengthwise and press the crease very firmly. This makes a tight V-shape or ‘tunnel.’
Hold the egg carton steady with the non-dominant hand. Use the dominant hand to aim the folded paper tunnel at a narrow slot.
Challenge your child to push the stiff paper all the way through the slot. Continue until the entire egg carton is full of paper tunnels!

Safety Tip:
Maintain constant adult supervision, especially during the preparation phase involving scissors. Although the paper pieces are large, ensure small torn scraps are collected immediately and kept away from the mouth.

Strong Punch Lacing Board

Steps:

Prep the cardboard by covering it with colored construction paper if desired. Use a marker to draw a simple shape or pattern on the board.
Hold the cardboard firmly with your helper hand. Challenge your child to squeeze the hole puncher hard to create holes around the drawn shape.
Cut a long piece of yarn. Tie one end of the yarn securely onto the first punched hole.
Thread the yarn through the holes, using both hands together to push and pull the string. Try to follow the drawn pattern.
When you reach the end, encourage your child to practice tying the two loose ends of the yarn into a simple knot. They must use precise pincer grips to manage the string.

Safety Tip:
Maintain constant adult supervision. Hole punchers can pinch fingers if not used properly. Small yarn pieces are a potential choking hazard for children who still place objects in their mouths.

Card Flipper Launch

Steps:

Hold the index card firmly with your helper hand. Cut 3 short, narrow slits across the center of the card using scissors. Keep the slits straight and tight.
Take a craft stick (the lever). Carefully push the stick through all three narrow slits. The stick should bend the card into a slight spring shape.
Set the lever structure down flat on the table. Place a bead onto the end of the craft stick using your thumb and pointer finger (pincer control).
Hold the index card base steady with your helper hand. Use one finger from your dominant hand to press the craft stick down slightly. Quickly release it to launch the bead toward the container target.

Safety Tip:
Beads are very small and pose a significant choking hazard. Close adult supervision is required throughout the entire activity. Ensure all small materials are collected and stored safely after play.